The Vault · $999 · Engineering Prototype

Hardware Spec

Every component chosen to hit 24 hrs runtime, five charging sources, and 12-month storage — fully offline, one-button boot.

System Architecture


  AC WALL (100–240V) ──►┌────────────────────────────────────────┐
  VEHICLE 12V ─────────►│   CHARGE BUS (14.6V LiFePO4 profile)   │
  SOLAR (MPPT) ────────►│   with input OR-ing / priority select  │
  USB-C PD 60W ────────►│                                        │
  HAND CRANK ──────────►└──────────────┬─────────────────────────┘
                                       ▼
                        ┌────────────────────────────────────────┐
                        │  LiFePO4 BATTERY 12.8V / 30Ah (384Wh)  │
                        │  Smart BMS w/ SHIP MODE (<50µA)        │
                        │  + MASTER MECHANICAL DISCONNECT        │
                        └──────────────┬─────────────────────────┘
                                       ▼
                 ┌────────────── DC DISTRIBUTION ───────────────┐
                 │  12V rail: display, amp, fan                 │
                 │  5V/5A rail: compute, USB hub, front bay     │
                 │  5V standby: RTC, power controller           │
                 └───┬──────────┬──────────┬──────────┬─────────┘
                     ▼          ▼          ▼          ▼
                 COMPUTE     15.6" IPS   AUDIO     USB BLOCK
                 (Pi 5 4GB)  DISPLAY     AMP+SPKRS (front bay + I/O)
            

Product Views

Open deck · pull-out power tray · rear charge inputs

Open Deck · Power System Access
Rear Panel · Five Charging Inputs

1. Compute Unit

~$146
#ItemSpecExample PartQtyEst.
1.1Single-board computerRaspberry Pi 5, 4GB RAM, quad A76Raspberry Pi 5 4GB1$60
1.2Active coolerOfficial Pi 5 active coolerRPi Active Cooler1$5
1.3NVMe adapterM.2 HAT (PCIe x1)Pimoroni NVMe Base or RPi M.2 HAT1$12
1.4Primary storage1TB NVMe SSD — Vault Library + My VaultCrucial P3 1TB1$60
1.5Boot storage32GB A2 microSD (OS, read-mostly)SanDisk Extreme 32GB1$7
1.6RTC backupCoin cell for Pi 5 RTC headerCR2032 + JST lead1$2
1.7Wi-Fi AP radioOnboard Pi radio running hostapd — no separate part———

Why Pi 5: ~5–10W draw, silent, runs the full stack — Kiwix, Jellyfin, RetroArch, hostapd, and the custom six-tile launcher — in ~2.5GB RAM while decoding 1080p H.264 comfortably.

2. Display — Lid Assembly

~$125
#ItemSpecExample PartQtyEst.
2.1Panel15.6" IPS, 1920×1080, eDP, matteBOE NV156FHM-N4S (or equiv.)1$60
2.2Driver boardeDP-to-HDMI controller w/ backlight PWM dimmingGeneric eDP LCD controller kit1$25
2.3Protective window3mm polycarbonate, AR filmCut-to-size1$15
2.4Lid mounting frameAluminum or laser-cut ACM frame + foam gasketCustom1$25
POWER NOTE: Panel + driver ≈ 5–7W at 60% brightness; up to ~10W at max. Dimming the screen is the highest-leverage runtime optimization.

3. Battery — LiFePO₄, 12-Month Storage

~$180

The 12-month rule: The Vault must sit in a closet for a year and boot when opened. LiFePO4 self-discharge is ~2–3% per month; the real enemy is parasitic drain from electronics.

"In storage, nothing may draw from the battery. Not the BMS, not the RTC, not an LED. Zero."
Layer 1
BMS Ship Mode
Quiescent draw under 50µA when triggered.
Layer 2
Mechanical Disconnect
Rotary switch physically isolates the pack — can't firmware-bug its way into draining.
Layer 3
Storage Doctrine
Store at 60–80% SoC. Vault OS 'Storage Mode' tops to 70%, syncs RTC, then triggers ship mode.
#ItemSpecExample PartQtyEst.
3.1Cells4× 3.2V 30Ah LiFePO4 prismatic (4S = 12.8V, 384Wh)EVE LF304$78
3.2Smart BMS4S 40A, ship mode, UART telemetry, low-temp cutoffJBD 4S 40A1$42
3.3Cell fixtureCompression plates, busbars, insulatorsKit1$18
3.4Master disconnectPanel-mount 60A rotary battery switch60A rotary switch1$14
3.5Main fuse40A MIDI at battery positiveFuse + holder1$8
3.6Battery enclosureVented ABS/aluminum sub-enclosure, foam isolationCustom1$20
3.7Low-temp guardBMS cutoff below 0°C charging (LiFePO4 must not charge below freezing)(BMS setting)——
RUNTIME MATH: 384Wh ÷ ~15W typical (compute 6W + display 5W + audio/hub 4W) ≈ ~24 hrs movies · 34+ hrs reading/audio at low brightness. BMS UART drives the deck gauge directly — no separate shunt needed.

4. Charging & Power — Five Sources

~$247

4.1 AC Wall Input

ItemSpecExampleEst.
AC-DC chargerExternal certified 14.6V 5A LiFePO4 brick, ships in the box—$26
AC inletPanel-mount barrel DC inlet, gasketed—$5

Mains conversion happens outside the case deliberately — the brick carries its own safety certification. Full-charge time: ~6 hours.

4.2 Solar Input

ItemSpecExampleEst.
MPPT charge controller10A MPPT, LiFePO4 charge profileGeneric 10A MPPT$32
Solar input jackPanel-mount XT60 (weatherized cap), 10–100W panels—$8
(Accessory) folding panel60–100W portable, sold separately as 'Vault Solar'100W folding CIGS/mono($150)

Full-charge: ~6 hours good sun (100W panel).

4.3 Vehicle 12V Input

ItemSpecExampleEst.
DC-DC charger12V → 14.6V CC/CV, 8A, LiFePO4 profileGeneric 8A DC-DC charger$16
Vehicle cableCig-plug → XT60, 10A fused—$10

Full-charge: ~3.5 hrs.

4.4 USB-C PD Input

ItemSpecExampleEst.
PD sink controllerNegotiates 20V/3A (60W) from any PD charger/power bankPD trigger/decoy module (fixed 20V)$8
Buck charger stage20V → 14.6V CC/CV LiFePO4 charge, 60W capSynchronous buck module w/ CC-CV$16
PortPanel-mount USB-C, charge-input labeled—$6

Full-charge: ~7 hrs.

4.5 Hand Crank (Human Power)

ItemSpecExampleEst.
GeneratorGeared dynamo, fold-out handle; sustained 10–15W realisticK-TOR Pocket Socket-class gear-motor, or 63:1 geared 775 motor$38
Rectifier + conditioningBridge rectifier + buck-boost into charge bus (accepts 5–30V wild input)Boost/buck module$10
Crank UXDeck LED + Vault OS 'CRANK' screen — live watts in (huge demo value)(BMS UART data)—

4.6 DC Distribution

ItemSpecExampleEst.
5V/5A buckBattery → compute + hub railPololu D24V50F5 or equiv.$12
12V rail protectionFused distribution block, 6-circuitBlue Sea ST-Blade mini$10
Charge-input OR-ingIdeal-diode modules preventing backfeed between sources2× ideal diode board$10
Soft power controllerMomentary VAULT POWER button → clean boot/shutdown (Pi GPIO), latching LED ringLoPo/ATXRaspi-style module + 22mm amber LED ring switch$18
Wiring12AWG (battery), 18AWG (rails), XT60/XT30, Anderson, heat-shrink, loom—$22
CRANK HONESTY: ~2Wh per 10 minutes of vigorous cranking — enough for a meaningful phone top-up or to bridge a gap. Use as a last-resort reserve, not a primary source.

5. USB Block & I/O Panel

~$64

Front "My Vault" Bay

ItemSpecQtyEst.
Powered USB 3.0 hub4-port, self-powered from 5V rail (no brownouts on drive insert)1$12
Panel-mount USB-A 3.0Front bay import ports2$10
Panel-mount USB-CFront bay (data)1$6

Protected I/O Panel (rear/side, gasketed door)

ItemQtyEst.
Panel-mount HDMI out (external TV/projector)1$8
Panel-mount 3.5mm headphone jack1$4
USB-A charge-out 5V/2.4A (phones — powered even when system is off)2$14
Sealed port door / rubber gaskets1 set$10

6. Audio

~$26
#ItemSpecExampleQtyEst.
6.1AmplifierClass-D stereo 2×10W, 12VTPA3116D2 board1$8
6.2Speakers2.5" full-range drivers, 4Ω, front-firing behind grillesDayton Audio PC83-42$18
AUDIO PATH: Audio rides HDMI from Pi into the amplifier — no separate DAC needed. Volume controlled from media remote and controllers.

7. Controls & Input

~$46
#ItemSpecExampleQtyEst.
7.1Controllers (included)Wired USB gamepads in fitted EVA recesses — no batteries to die, no pairing, nothing to loseWired USB gamepads2$34
7.2Media remote2.4GHz mini remote w/ USB dongle (no pairing ritual)Rii-class air remote1$12

8. Case & Mechanical

~$188
#ItemSpecExampleQtyEst.
8.1CaseRugged wheeled/handled, ~20×12×8" interior, IP-rated when latchedApache 4800 (proto) / Pelican 1600-class (production)1$60
8.2Deck plate6mm HDPE or aluminum composite, CNC-cut for controls/recessesCustom1$30
8.3Lid frameDisplay mount + cable pass-through friction-hinge zoneCustom1$25
8.4FoamCNC/laser-cut EVA fitted recesses — controllers, remote, cablesCustom1$28
8.5Pressure ventGore-type vent (altitude/temp equalization; required with sealed case + battery)—1$8
8.6Fasteners/standoffsM3/M4 stainless, brass inserts, rubber isolation mounts (battery)Kit1$15
8.7Thermal1× 40mm quiet fan, thermostat-switched above 45°C, filtered intakeNoctua NF-A4x101$12
8.8LabelsLaser-etched port labels, brand plate, power-hierarchy legend—1$10

9. Software Stack

OS
Raspberry Pi OS Lite (64-bit), read-only root — power-cut safe
Launcher
Custom six-tile Vault OS front end (Electron/Flutter kiosk)
LEARN / SURVIVE
Kiwix + ZIM library — Wikipedia, WikiMed, iFixit, Project Gutenberg, FEMA manuals
WATCH
Jellyfin — also serves offline Wi-Fi clients on the local AP
PLAY
RetroArch / EmulationStation — open-source and licensed homebrew only
MY VAULT
File manager + LUKS-encrypted partition, PIN-unlocked
Offline Wi-Fi
hostapd + dnsmasq captive portal → Vault web UI at vault.local
Power UI
BMS UART telemetry driving battery %, runtime estimate, live crank watts
TV control
`libcec` systemd service — One Touch Play on boot, System Standby on shutdown
$0 SOFTWARE LICENSE COST — every piece of this stack is open-source.

10. Cost Roll-Up

Single Prototype BOM

Compute$146
Display$125
Battery (LiFePO4 384Wh)$180
Charging & power (5 sources)$247
USB block & I/O$64
Audio$26
Controls$46
Case & mechanical$188
Prototype Total≈ $1,022
The Vault
Pi 5 4GB / 30Ah / 1TB / 15.6" panel / 2 wired controllers
$999
>_ THE OFFLINE VAULT · 100% OFFLINE · SYS_READY

Power Budget

Operating StateDrawRuntime on 384Wh
Movie night (screen 60%, audio, 2 controllers)~15W~24 hrs
Reading / Wikipedia (screen 30%)~11W~34 hrs
Wi-Fi library server, screen off~8W~48 hrs
Phone-charging station only~12W out~28 phone charges
Storage (ship mode + master switch off)~0µA effective12+ months — wakes at ~45–55%

Charge Times (0 → 100%, 384Wh)

SourceInput PowerEst. Full Charge
Vehicle 12V~117W~3.5 hrs
AC brick (included)~73W~6 hrs
Solar 100W panel~65W~6 hrs good sun
USB-C PD (60W)~60W~7 hrs
Hand crank~9W netReserve use only

Safety & Compliance

Production — not prototype
Battery
UN 38.3 transport testing, IEC 62133; LiFePO4 low-temp charge lockout mandatory.
EMC / Radio
FCC Part 15 / CE RED for the Wi-Fi AP.
Electrical
UL/IEC 62368-1 for the AC charging path — or ship an external certified brick to simplify V1.
Shipping
>100Wh pack = Class 9 dangerous-goods shipping. Affects crowdfunding logistics more than founders expect — factor in early.

Build Order (Prototype)

01
Bench-assemble power system first
Cells → BMS → master switch → charge bus. Verify all five inputs charge correctly and ideal diodes block backfeed.
02
Validate ship-mode quiescent current
Measure with a µA meter. Pass/fail gate for the 12-month storage claim — do not proceed until this passes.
03
Bring up compute stack on bench power
Pi 5 + NVMe + display on bench supply. Install and verify the full software stack before case integration.
04
Integrate into case
Battery bay → deck plate → lid/display → wiring loom. Keep all connections serviceable.
05
Thermal soak test
4-hour movie playback at 35°C ambient with lid at 90°. Fan must hold CPU temps under 70°C.
06
Full runtime discharge test
Run to depletion under realistic movie-night load. Calibrate fuel gauge. Confirm 24-hour target.
07
30-day storage test
Trigger ship mode, measure SoC delta at day 30, extrapolate to 12-month projection. Validate the zero-drain claim.
Be First

Built to Last.

Reserve your place before production decisions are locked in. No payment required.